This website uses cookies to ensure that we give you the best experience on our website.
By continuing to browse the site you are agreeing to our use of cookies. To find out more click here

Weber - Saint-Gobain

weberjoint wide flex

weberjoint wide flex
weberjoint wide flex

Product Benefits

  • Suitable for interior and exterior use
  • Suitable for dry and wet conditions
  • Recommended for wooden floors
  • Recommended when tiling floors with underfloor heating or undertile warming

A wide-joint, mould-resistant, flexible tile grout for interior and exterior use

For grouting joints between wall and floor tiles:

Product Features

About this Product

weberjoint wide flex is a wide-joint, cement-based, flexible tile grout for interior and exterior use in situations where some movement or vibration is expected.

It can be used for grouting ceramic, porcelain, mosaic, quarry, natural stone, terrazzo and terracotta tiles and brick slips.

Features and Benefits

  • Manufactured under BSI Quality Assurance Scheme ISO 9001
  • Suitable for joint widths up to 20mm
  • Abrasion resistant
  • Can be used on walls and floors
  • Limited flexibility to absorb movement from wooden floors or underfloor heating
  • Available in the following colours:-
    white
    ivory
    cream
    limestone
    sandstone
    beige
    grey
  • Contains Mould Stop Technology for lasting protection from mould growth

Constraints

Not suitable if the grout is required to be chemically resistant or completely impermeable.

Special care is required if the tiles have a soft face/glaze.

Technical Services

Weber's Customer Services Department has a team of experienced advisors available to provide on-site advice both at the specification stage and during application. Detailed specifications can be provided for specific projects or more general works. Site visits and on-site demonstrations can be arranged on request.

Technical helpline
Tel: (01525) 722110
Fax: (01525) 718988

Documentation

Send or download the documents

You can either send the documents to an email address, or download it

Preparation & Application

Preparation

Ensure that all the adhesive has set and dried, and that the tiles are firm.

Adhesive should normally be left for at least 24 hours before grouting, unless using a rapid set adhesive, when it should normally be left for 2 - 3 hours. Longer may be required on sealed or impervious surfaces.

Ensure that tiles and joints are clean and free from grease or any other contamination.

If the grout is required to be completely impervious to water, or chemically resistant, use weberjoint epoxy.

Mixing

It is recommended that a low-speed mechanical mixer is used.  Gradually add 4 parts of grout to 1 part (by volume) of clean water and mix to a smooth, stiff, workable paste.  After mixing, allow the mix to stand for 5 minutes and add more powder if necessary. Re-mix thoroughly.

Do not re-wet or add too much water, as this will cause the set grout to be weak, with a tendency to crumble. It may also cause surface discolouration and variaton, especially with dark colours.

Application

Do not use at temperatures below 5°C.
Using a squeegee or a rubber float, apply the grout to a small area at a time. Completely fill the joints leaving no voids. Excess grout should be removed immediately using a rubber float held at 90° to the tiles. This should be moved diagonally across the tiles to prevent removal of grout within the joints.

When the grout has started to dry, after 5 - 10minutes (less at temperatures above 20°C) the tiles should be cleaned with an emulsifying pad. This should be used in a circular motion to loosen the grout residue. The tiles should now be wiped with a clean damp sponge until all residue is removed.

When dry, polish the tiles with a clean, dry cloth.

Tools and equipment should be washed in water immediately after use.

Warning
Some tiles may have a soft surface which can be scratched during grouting.

Some tiles with a matt or porous texture are prone to surface staining when coloured grouts are used. The use of an appropriate protective sealer is recommended.

Some tile faces have shallow depressions that can fill with grout. This grout must be removed before it hardens. When using a grout that is a similar colour to the tiles, it can be difficult to see any residue that is left in these shallow depressions. It is recommended that in these instances the tiles should be treated with an appropriate protective sealer that helps to stop grout sticking to the tile face.

You are advised to test the grout on a spare tile before proceeding.

An admix should not be used with this grout, as it will make it difficult to use and could cause the grout to crack.Allowance for movement
Flexible joints should be incorporated to allow for slight movements due to changes in temperature, humidity etc. as indicated by BS5385:
a) where the tiling meets other materials (e.g. floor perimeters)
b) along all internal corners - vertically and horizontally
c) over existing movement joints or changes in background material
d) dividing large tiled areas into bays (every 3 - 4.5 m on walls, 8 - 10 m on floors)

Packaging, Health & Safety

Storage and Shelf Life

When stored unopened in a cool, dry place at temperatures above 5°C, shelf life is 12 months from date of manufacture. If stored longer, setting times will increase.

Packaging

 weberjoint wide flex is packed in 5kg & 10kg plastic lined paper sacks

Health and Safety

Contains cement.