About this Product
webertec EP mortar is available as a three-component bulk pack or as a two-component handy pack, consisting of epoxy resin, hardener and selected graded aggregates (filler) which, when mixed, produce a high-strength, impermeable and chemically-resistant mortar.
Conforms with BS EN 1504-3.
Features and Benefits
- Fast epoxy repair - stronger than concrete in less than 24 hours
- High strength - 2 to 3 times stronger than normal concrete.
- Impermeable to water, oil, petrol, chemical spillage.
- Easy to mix and apply.
weber's Customer Services Department has a team of experienced advisors available to provide on-site advice both at the specification stage and during application. Detailed specifications can be provided for specific projects or more general works. Site visits and on-site demonstration can be arranged on request.
Tel: (01525) 722110
Fax: (01525) 718988
weber products are ditributed throughout the UK through selected stockists and distributors. For UK sales enquiries and overseas projects, contact weber's Sales office.
Tel: (01525) 722100
Fax: (01525) 718988
Material Safety Datasheet
- Material Safety Datasheet 1 - webertec EP mortar
- Material Safety Datasheet 2 - webertec EP mortar
- Material Safety Datasheet 3 - webertec EP mortar
Declaration of Performance (DoP)
Preparation & Application
As with all concrete repairs it is essential to remove all grease, oil, dust and other loose materials.
Concrete substrates must be adequately prepared either by use of a suitable mechanical method such as scabbling, grit blasting or needle gunning, or by such other means as appropriate. Concrete bases for toppings must be carefully prepared to give a clean freshly exposed sound roughened surface.
Old concrete surfaces contaminated with oil or grease require suitable preparation such as steam cleaning in conjunction with a suitable detergent.
Care must be taken to ensure that the oil or grease is removed from the surface and not simply spread over a larger area.
Steel substrates should first be grit blasted to BS 7079-A1 equivalent to Swedish Standard Specification SA 2 1/2, followed by degreasing with a suitable solvent (e.g. webertec solvent 3) immediately prior to bonding. However, in many instances where corrosion is absent, wire brushing to a clean bright surface may be adequate, but care must be taken not to just polish the rust on the surface.
The bond of webertec EP mortar will be improved by the application of a bond coat of webertec bonding aid, both of which are moisture-tolerant primers.
In all cases the webertec EP mortar must be applied whilst the primer coat is still tacky.
When applying webertec EP mortar to vertical surfaces, webertec EP bonding aid should be used as the bond coat.
For the large packs, the resin and hardener should first be thoroughly mixed to an even colour and consistency before adding the filler. The quantity of the filler may be adjusted to achieve a less viscous consistency, but should never be less than the amount detailed on the packaging.
The small packs have filler is included in resin and hardner components.
The mortar should be applied using a steel trowel in layers of up to 20 mm thick.
Allow initial set (6 hours approximately) between layers. On vertical surfaces the maximum thickness should be 12 mm.
The mortar should be well tamped to ensure proper consolidation and then trowelled to bring up enough resin binder to thoroughly seal the surface.
Feather edging must be avoided. The edges of all repairs should be "toed in" i.e. cut back so the minimum thickness is not less than 5 mm.
webertec EP mortar can be applied to vertical surfaces as well as horizontal. Weber has a range of cementitious mortars, which may be more suitable to a particular application.
Uncured material may be removed with webertec solvent 3
Clean all tools etc, with webertec solvent 3 immediately after use.
Packaging, Health & Safety
webertec EP mortar is supplied in two pack sizes
5 kg pack - yield approximately 2·7 litres
26 kg pack - yield approximately 12.5 litres
The 26 kg pack is supplied as a 6-way split pack.
Storage and Shelf Life
The shelf life of webertec EP mortar is in excess of 12 months if stored in cool, dry, frost free conditions.
Health and Safety
Contains epoxy constituents. Refer to information supplied by manufacturer (see Material Safety Data Sheet).
All skin contact with epoxy resin products should be avoided. Barrier creams should be used and operatives should wear protective clothing including gloves. Working areas should be well ventilated.
The hardener content is alkaline and labelled as corrosive. The resin content is labelled as an irritant. The flash point of all components is in excess of 100°C. In the event of fire use foam, dry chemical, carbon dioxide or water fog extinguishers.
For critical structural applications and applications in exposed situations where very high surface temperatures may be recorded, please contact our Technical Sales Department for further advice before use.
For further information, please request the Material Safety Data Sheet for this product
Other products in the range
Polymer-modified cementitious bonder for repair mortars
Acrylic-polymer modified, highbuild façade repair mortar
Acrylic-polymer modified, high build structural repair mortar
Polymer modified, cementitious bonding aid
Preblended, polymer modified, dense cementitious repair mortar
High build cementitious mortar for vertical and soffit repairs
Low-resistivity, polymer-modified, Highways Agency Class M patching mortar and render for cathodic protection
Low-resistivity, dry-spray, structural repair concrete
Shrinkage compensated, high strength, flowing repair concrete.
Shrinkage-compensated, highstrength, low-resistivity, flowing repair concrete for recasting in conjunction with cathodic protection systems.
Preblended, single-component, polymer-modified cementitious levelling mortar.
Sealer for hairline cracks in concrete and treatment of hollow floor screeds
Economical, cement-based, dry-spray concrete
Moisture-tolerant epoxy primer for bonding epoxy repair mortars and new cement mixes to existing concrete
Polymer-modified, dry-spray, structural repair concrete
Polymer-modified, dry-spray, structural repair concrete with fibre-reinforcement
Rapid-setting, polymer-modified, dry-spray concrete
BS EN 1504 compliant concrete patch repair system
Fast-setting, multi-purpose mortar