About this Product
Preblended, single-component, polymer-modified, cementitious mortar needing only mixing with water to produce a high quality surface levelling mortar and pore filler for most concrete surfaces.
This product has been formulated to comply with the requirements of BS EN 1504-3.
Features and Benefits
- Dual action - can be used as a pore filler and a levelling mortar
- Easy to apply: does not slump or slip
- Easy to spread to provide a smooth and level surface
- Good adhesion to prepared concrete
- Compatible with typical concretes
- Good carbonation resistance: contributes to the properties of the Mulsifix Concrete Repair System
- Allows water vapour to escape - does not trap water vapour - does not blister
Formulated to comply with the requirements of BS EN 1504-3
weber Customer Services Department has a team of experienced advisors available to provide on-site advice both at the specification stage and during application. Detailed specifications can be provided for specific projects or more general works. Site visits and on-site demonstrations can be arranged on request.
Tel: (01525) 722110
Fax: (01525) 718988
weber products are distributed throughout the UK through selected stockists and distributors. For UK sales enquiries and overseas projects, contact Weber's Sales office.
Tel: (01525) 722100
Fax: (01525) 718988
Material Safety Datasheet
Declaration of Performance (DoP)
Preparation & Application
webercem fairing coat is suitable for use on concrete and dense concrete blockwork. lt is not suitable for lightweight blocks or bricks.
All substrates must be sound, free of all contamination including laitance, paints, coatings, oil, grease and dust.
Concrete and concrete blockwork surfaces must be adequately prepared by use of suitable mechanical means such as grit blasting, high pressure water jetting or needle gunning to produce a lightly textured surface to ensure a good key.
Concrete surfaces contaminated with oil or grease require suitable preparation. New concrete must be fully cured for at least 14 days. Do not use a permanent curing membrane.
Defects such as honeycombing, leaks, pinholes, cracks etc. should be treated appropriately prior to the application of webercem fairing coat. Pinholes, blowholes, small voids and pores can be treated with webercem fairing coat as described below. Cure fresh repairs for at least 24 hours.
Thoroughly dampen the area to be treated with clean water and allow excess to drain off before applying webercem fairing coat.
Mix webercem fairing coat in a forced-action mixer or in a clean bucket using a paddle and a slow speed drill at a speed not exceeding 400rpm. Mix for at least 2 minutes to a smooth and homogenous paste consistency. For normal levelling applications use 3 to 3.5 litres of water per 25 kg bag. For other applications such as pore filling, dubbing out, etc. the water addition can be varied depending on the consistency required and the ambient temperature.
Min. water addition: 3 litres per 25 kg bag Max. water addition: 3.5 litres per25 kg bag. Usable time after re-mixing: > 45 minutes. For small quantities, mix 1 part water to 4.5 parts of powder by volume.
Ensure all pores, surface voids etc. are filled first before applying webercem fairing coat as a levelling mortar.
For pore filling: Use a pallette knife or similar tool to apply the mortar, pressing well into the pores. Alternatively, use a damp sponge to rub the mortar into the pores with a circular motion. Finish flush to the surface and rub off any excess mortar. It is best to allow the pore-filling mortar to harden first before re-wetting and applying the levelling coat.
Maximum depth and diameter of application: 5 mm
For surface levelling: Apply with a steel float to a thickness of about 2 mm pressing well into the damp substrate. lf a thicker coat is needed to hide deeper surface imperfections, apply the second coat when the mortar has hardened sufficiently to support it.
Minimum thickness of application: 1 mm per layer.
Maximum thickness of application: 3 mm per layer up to a combined maximum of 5 mm.
A spray pump can be used when levelling large areas of concrete.
Use a steel float to provide a smooth surface when the mortar has firmed up sufficiently. Do not re-wet the surface before trowelling. This may cause some surface crazing.
Alternatively, rub up with a wooden float or sponge to produce a level surface suitable for overcoating.
Normal concrete curing methods are recommended. Do not use a curing agent when applying a coating unless it can be proven that the subsequent bond will be unimpaired.
webercem fairing coat
Temperature range of application: +5°C to +35°C. Do not apply on frozen surfaces or when frost is expected within 24 hours. Do not apply in direct sunlight or on hot substrates.
When applying in confined or close spaces, cure for 3 days then ensure sufficient ventilation to prevent condensation.
Note: Times quoted need to be extended at lower temperatures and reduced at higher temperatures.can be overcoated by one of the anti-carbonation coatings in the webercote range. Overcoating times are dependent on weather conditions.
Packaging, Health & Safety
Supplied in 25 kg bags.
Coverage / Yield
Actual yield depends on the water mix ratio.
Approx 3.8 kg per m2 when applied at 2 mm thickness.
Approx. 6.5 m2 per 25kg at 2 mm.
Yield approx. 13 litres.
Storage and Shelf Life
When stored unopened in a dry place at temperatures above 5°C, shelf life is 12 months from date of manufacture.
Health and Safety
Contains cement (Contains chromium (VI). May produce an allergic reaction). Harmful by inhalation. Irritating to eyes and skin. Keep out of the reach of children. In case of contact with eyes, rinse immediately with plenty of water and seek medical help. After contact with skin, wash immediately with plenty of soap and water. Wear suitable protective clothing, gloves and eye/face protection.
For further information, please request the Material Safety Data Sheet for this product.
Other products in the range
Polymer-modified cementitious bonder for repair mortars
Acrylic-polymer modified, high build structural repair mortar
Polymer modified, cementitious bonding aid
Preblended, polymer modified, dense cementitious repair mortar
High build cementitious mortar for vertical and soffit repairs
Low-resistivity, polymer-modified, Highways Agency Class M patching mortar and render for cathodic protection
Low-resistivity, dry-spray, structural repair concrete
Shrinkage compensated, high strength, flowing repair concrete.
Shrinkage-compensated, highstrength, low-resistivity, flowing repair concrete for recasting in conjunction with cathodic protection systems.
Sealer for hairline cracks in concrete and treatment of hollow floor screeds
Economical, cement-based, dry-spray concrete
Moisture-tolerant epoxy primer for bonding epoxy repair mortars and new cement mixes to existing concrete
Acrylic-polymer modified, highbuild façade repair mortar
Polymer-modified, dry-spray, structural repair concrete
Polymer-modified, dry-spray, structural repair concrete with fibre-reinforcement
Rapid-setting, polymer-modified, dry-spray concrete
High strength epoxy resin mortar for repairs, bedding and fixing
BS EN 1504 compliant concrete patch repair system
Fast-setting, multi-purpose mortar