weber.renddash 

weber.rend dash is a one-coat render designed to receive a dry dash finish. The ability to apply and finish in one coat avoids the drying times associated with two-coat systems. This allows fast application with shorter programme periods, thereby reducing associated scaffolding and site costs and permitting the completion of ground works at an earlier stage.

• One coat for fast application and short programme periods
• Factory produced for consistency of proportioning
• Ready mixed – only water required to be added on site for ease of use
• Suitable for hand or machine application

weber.rend dash is available in 3 colours, 675 white, 632 cream and 672 Grey.

A range of decorative aggregates are available to complement weber.rend dash.

Final colour selection must be made against an actual sample. Weber will not accept responsibility for colours chosen from any source other than an actual sample.

Colour samples are freely and readily available from Weber.  

weber.rend dash complies with mix designation III (1:1:6) as set out in BS 5262 and BS 5492.  

weber.rend dash can be applied to most, suitably prepared masonry backgrounds.

All surfaces must be sound, clean, suitably dry and free of any material which may impair adhesion.

Substrates must have a good mechanical key suitable for rendering. The use of weber.rend aid will provide an artificial key on substrates such as smooth concrete.  

Mechanically mix in a suitable batch or continuous-mix spray render machine using clean water only.

A suitable drill and whisk or tumble mixer can also be used when hand application is required. Gradually add the contents of the bag to 4.5 – 5 litres of water and mix for 5 to 10 minutes.

To ensure colour consistency, the materials required for complete and adjoining panels should be of the same batch number or be thoroughly mixed together before use.  

To avoid dampness and discolouration of finishes, rendering should be avoided below DPC or within 150 mm of ground level. weber.rend dash should be applied in one coat with two passes. Each pass should be applied by hand (hawk and trowel) or machine render pump then ruled level. The first pass should be left for approximately one hour before application of the second pass and finish.

Render thicknesses are as for traditional materials

● Moderate exposure overall thickness approx 16mm - first pass 10mm second pass 6mm

● Severe exposure overall thickness approx 20mm – first pass 12mm second pass 8mm

Thickness should not exceed 25mm.  

All equipment must be washed with clean water immediately after use. Waste material should not be emptied into drainage systems.  

For each mm of thickness you will require approximately 1.8 kg per m².

When applied at 16mm thick, coverage is approximately 35 m² per tonne.

Note: These estimates take no account of wastage and may vary according to the type of surface involved. An allowance must be made for uneven and misaligned substrates when ordering materials.  

Store in a cool dry place. Shelf life of unopened bag, in correct storage conditions, is at least 12 months.  

Contains cement (Contains chromium (VI). May produce an allergic reaction). Harmful by inhalation. Irritating to eyes and skin. Keep out of the reach of children. In case of contact with eyes, rinse immediately with plenty of water and seek medical help. After contact with skin, wash immediately with plenty of soap and water. Wear suitable protective clothing, gloves and eye/face protection.

For further information, please request the Material Safety Data Sheet for this product.  

Weber's Customer Services Department has a team of experienced advisors available to provide on-site advice both at the specification stage and during application. Detailed specifications can be provided for specific projects or more general works. Site visits and on-site demonstrations can be arranged on request.

Technical helpline
Tel: (01525) 722110
Fax: (01525) 718988

Weber products are distributed throughout the UK through selected stockists and distributors. Please contact the relevant Customer Services Team below for all product orders and enquiries.

England and Wales

Tel: 01525 722100

Fax: 01525 718988

Scotland, Northern Ireland, Isle of Man, Republic of Ireland

Tel: 028 9335 2999

Fax: 028 9332 3232