weber.plastTF and DF(troweltex and trowelcoat)

weber.plast TF and weber.plast DF are acrylic based, composite, decorative finishes, pre-mixed and ready to apply in wet form.

• Factory batched and ready to use
• Excellent all-round weather performance
• Durable and resilient
• Technical support from a Quality Assured company
• Established track record in varying climatic conditions
• Forms part of a number of BBA approved insulation systems

weber.plast TF and weber.plast DF are available in a wide range of colours. Specifiers should consult the NCS Colour Chart on the Weber website www.netweber.co.uk

Final colour selection must be made against an actual sample. Weber will not accept responsibility for colours chosen from any source other than an actual sample.

Colour samples are freely and readily available from Weber.

The quality of application of this material depends on suitable operative skills and product familiarity.

Restrictions on weather conditions during application and curing must be respected.

Sound trade practices and printed instructions must be followed.

Good access and appropriate protection must be provided.

weber.plast TF and weber.plast DF are wet pre-mixed materials contained in 15kg sealed polythene buckets. They are applied to prepared surfaces on to a tinted primer.

Prime the prepared surface using weber PR310 applied by brush or spray. Ensure complete coverage of wall to be treated to prevent 'grinning through' of the background. Primer is of low viscosity and easily applied. Check batch numbers and colours of material required to complete working area. Stir well in buckets and make minor adjustments to workability with a little water, thoroughly mixed in.

Apply weber.plast TF or weber.plast DF with a steel float and hawk to work area. Use a thin plastic float to finish weber.plast TF and a wooden or plastic float to create drag or swirl effects with weber.plast DF.

Evenness of cover and texture are of paramount importance. Agree acceptable finished appearance on a sample area with architect or supervising officer before proceeding with large-scale application. Maintain a steady flow of application and keep a wet edge on all incomplete areas.

weber.plast TF and weber.plast DF are synthetic materials, therefore weather conditions for applying and drying are critical. Dry weather may not be enough if the humidity is high and the drying potential of the atmosphere is low. A dry atmosphere which can be foreseen for about 36 hours is preferred to effect initial curing and prevent wash-off. Otherwise proper weather protection for the work may be necessary.

Synthetic mixes can stain and are difficult to remove so protect vulnerable areas thoroughly and wear protective clothing, particularly gloves.

Good Practice:

Do not apply:-

• If frost is forecast within 24 hours of use
• In damp wet conditions
• In temperatures below 5°C or above 30°C
• On elevations in direct sunlight or where the substrate is hot 

Wet pre-mixed materials must be stored frost-free and protected from direct sunlight and extreme heat. To prevent ingress of air, buckets should be stacked no more than 2 high, and where a central support is used, to a maximum height of 4. When stored under these conditions, the shelf life of the product is 12 months from the date of manufacture.

Essentially not hazardous.
Not harmful during normal use.
After contact with skin, wash immediately with plenty of water.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
Keep out of the reach of children.

For further information, please request the Material Safety Data Sheet for this product.

weber's Customer Services Department has a team of experienced advisors available to provide on-site advice both at the specification stage and during application. Detailed specifications can be provided for specific projects or more general works. Site visits and on-site demonstrations can be arranged on request.

Technical helpline
Tel: (01525) 722110
Fax: (01525) 718988

Sales, England and Wales
Tel: (01525) 722100
Fax: (01525) 718988

Sales, Scotland
Tel: (0141) 445 0121
Fax: (0141) 445 0122

Sales, Ireland
Tel: (028) 9335 2999
Fax: (028) 9332 3232