About this product
weber.cote EC is a single-part aqueous exterior coating based on an acrylic elastomer to provide a high build protective, elastomeric and decorative finish to exposed concrete and other surfaces.
This product has been formulated to comply with the requirements of BS EN 1504-2.
Features and Benefits
- High build: 0.5 mm in thickness, thicker than most other coatings. Better resistance to movement
- Will bridge static cracks over 3mm
- Very good dynamic crack bridging capability
- Excellent anti-carbonation coating.
- Allows water vapour diffusion.
- Available in a range of colours with good colour retention.
- Durable life expectancy in excess of 15 years.
-
This product has been formulated to comply with the requirements of BS EN 1504-2
-
Agrément approved as part of the weber.cem Concrete Repair System.
Colours
weber.cote EC is available in the colours from the standard, premium and designer ranges. Specifiers should consult the Colour Charts, available from weber, and whenever possible, obtain samples prior to specification.
Technical data
Constraints
As weber.cote EC is cured by UV light, a longer cure period may be required on the interior of buildings. It should not be used on water-retaining structures or in situations where ponding of water will occur.
Preparation
If considered necessary, substrates should be primed with weber.cote primer. New surfaces should be clean, sound and dry. Concrete must be free of coating such as mould oil and any laitance should be removed, following which the surface can be primed with weber.cote primer. Old surfaces must also be clean, sound and dry. Glossy surfaces should be roughened to provide a key. Lichen, moss or fungal growth must be removed and the areas treated with weber CL150 in accordance with the instructions on the data sheet*.
Chalky or friable surfaces, or previously decorated surfaces which are flaking, should be wire-brushed to remove loose materials and then stabilised by one coat of weber.cote primer.
Static cracks up to 3 mm wide can be covered with weber.cote EC - ensure material is brushed well into crack. Wider cracks should be filled with weber.cem fairing coat and allowed to dry, then spanned with a fabric mesh such as mesh NT prior to coating.
* Full data sheet available from weber on request
Application
It is recommended that the coating is well stirred prior to use. A two-coat application is required - apply by brush or long haired roller at a minimum of 400 μm wet film thickness per coat. weber.cote EC is designed as a thick coating material, do not brush or roller out, i.e. overspread. Allow to dry for at least 24 hours between coats. Nominal drying time approx. 4 hours at 20°C; full cure in 2 to 3 weeks. weber.cote EC should be applied when ambient or surface temperatures are above 4°C. Do not apply below 4°C or when frost is expected.
Maintenance
weber.cote EC will require little maintenance. lt can be washed down using clean water with a soft bristle brush. Re-coating should not be necessary for approximately 10 years, but can be carried out after thorough cleaning of the coating.
EU VOC regulations 2008
EU limit for weber.cote EC (cat A/c):
75 g/l (2007)/40 g/l (2010). weber.cote EC contains <30 g/l VOC.
Cleaning
Clean brushes or roller in water immediately after use. lf they become clogged, soak in very hot water containing a mild detergent.
Coverage / Yield
Storage and Shelf life
Protect from frost. Store in clean, dry conditions between 5°C and 30°C. When stored in correct conditions a shelf life of 2 years can be expected. lt is recommended that the coating be stirred well prior to use after it has been in storage for some time.
Fire Properties
weber.cote EC, when applied to a noncombustible substrate, has a Class 1 surface. The weber.cem concrete repair system has a Class 0 surface for fire propagation.Health and Safety
Essentially not hazardous
Not harmful during normal use.
After contact with skin, wash immediately with plenty of water.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advise.
Keep out of reach of children.
For further information, please request the Material Safety Data Sheet for this product
Technical services
weber's Customer Services Department has a team of experienced advisors available to provide on-site advice both at the specification stage and during application. Detailed specifications can be provided for specific projects or more general works. Site visits and on-site demonstrations can be arranged on request.
Technical helpline
Tel: (01525) 722110
Fax: (01525) 718988
Sales Contact
weber products are distributed throughout the UK through selected stockists and distributors. For UK sales enquiries and overseas projects, contact weber's Sales office.
Sales office
Tel: (01525) 722100
Fax: (01525) 718988
